Physics · 042D-042-2025·Delhi Scheme

Jump to:
1
Section A()
1 Mark
A uniform electric field pointing in the positive X-direction exists in a region. Let A be the origin, B be the point on the X-axis at x=+1 cmx = +1\text{ cm} and C be the point on the Y-axis at y=+1 cmy = +1\text{ cm}. Then the potentials at points A, B, and C satisfy:
(a) VA<VBV_A < V_B
(b) VA>VBV_A > V_B
(c) VA<VCV_A < V_C
(d) VA>VCV_A > V_C
CBSE Official Step-Marking AllocationTotal: 1 M
State that electric potential decreases along the direction of the electric field (dV=−E dxdV = -E \, dx)
+0.5 M
Conclude VA>VBV_A > V_B and VA=VCV_A = V_C, identifying option (b)
+0.5 M
NCERT / CBSE Model Answer
Correct Option: (b) VA>VBV_A > V_B
Reasoning:
1. In the direction of an electric field, the electric potential always decreases: E=−dVdxE = -\frac{dV}{dx}. Since the field points along the +X+X-direction, potential decreases as xx increases. Hence, VA>VBV_A > V_B because xA=0<xB=1 cmx_A = 0 < x_B = 1\text{ cm}.
2. Point C is on the Y-axis (x=0,y=1 cmx = 0, y = 1\text{ cm}). The Y-axis is perpendicular to the electric field (equipotential line for a field in the X-direction). Thus, VA=VCV_A = V_C.
Therefore, the correct relation is VA>VBV_A > V_B.
Chief Examiner Evaluation Report & Pitfalls:

Equipotential surfaces are always perpendicular to electric field lines. Along the field lines, potential strictly decreases.

2
Section A()
1 Mark
A conducting wire connects two charged conducting spheres of radii r1r_1 and r2r_2 such that they attain equilibrium with respect to each other. The distance of separation between the two spheres is very large as compared to either of their radii. The ratio of the magnitudes of the electric fields at the surfaces of the spheres of radii r1r_1 and r2r_2 is:
(a) r1r2\frac{r_1}{r_2}
(b) r2r1\frac{r_2}{r_1}
(c) r22r12\frac{r_2^2}{r_1^2}
(d) r12r22\frac{r_1^2}{r_2^2}
CBSE Official Step-Marking AllocationTotal: 1 M
Equate potentials V1=V2  ⟹  q1/q2=r1/r2V_1 = V_2 \implies q_1/q_2 = r_1/r_2
+0.5 M
Substitute into E1/E2=(q1/q2)(r2/r1)2=r2/r1E_1/E_2 = (q_1/q_2)(r_2/r_1)^2 = r_2/r_1 and select option (b)
+0.5 M
NCERT / CBSE Model Answer
Correct Option: (b) r2r1\frac{r_2}{r_1}
Working:
In electrostatic equilibrium, connected conducting spheres reach the same electric potential:
V1=V2  ⟹  kq1r1=kq2r2  ⟹  q1q2=r1r2V_1 = V_2 \implies \frac{k q_1}{r_1} = \frac{k q_2}{r_2} \implies \frac{q_1}{q_2} = \frac{r_1}{r_2}

The electric field at the surface of a conducting sphere of radius rr is E=kqr2E = \frac{k q}{r^2}.
Taking the ratio of surface electric fields:
E1E2=kq1/r12kq2/r22=(q1q2)(r22r12)=(r1r2)(r22r12)=r2r1.\frac{E_1}{E_2} = \frac{k q_1 / r_1^2}{k q_2 / r_2^2} = \left(\frac{q_1}{q_2}\right) \left(\frac{r_2^2}{r_1^2}\right) = \left(\frac{r_1}{r_2}\right) \left(\frac{r_2^2}{r_1^2}\right) = \frac{r_2}{r_1}.
Chief Examiner Evaluation Report & Pitfalls:

Electric field at the surface of a conductor is inversely proportional to radius when potentials are equal: $E = V/r$.

3
Section A()
1 Mark
A long straight wire of circular cross section of radius aa carries a steady current II. The current is uniformly distributed across its cross section. The ratio of magnitudes of the magnetic field at a point a/2a/2 above the surface of the wire to that of a point a/2a/2 below its surface is:
(a) 4:14:1
(b) 1:11:1
(c) 4:34:3
(d) 3:43:4
CBSE Official Step-Marking AllocationTotal: 1 M
Apply Ampere's law for r1=3a/2r_1 = 3a/2 (outside) and r2=a/2r_2 = a/2 (inside)
+0.5 M
Compute ratio of magnetic fields to get 4:34:3 and select (c)
+0.5 M
NCERT / CBSE Model Answer
Correct Option: (c) 4:34:3
Working:
1. Point P1P_1 at distance a/2a/2 above the surface: distance from wire axis is r1=a+a/2=3a2r_1 = a + a/2 = \frac{3a}{2}.
For r>ar > a, magnetic field outside a cylindrical wire:
B1=μ0I2πr1=μ0I2π(3a/2)=μ0I3πa.B_1 = \frac{\mu_0 I}{2\pi r_1} = \frac{\mu_0 I}{2\pi (3a/2)} = \frac{\mu_0 I}{3\pi a}.

2. Point P2P_2 at distance a/2a/2 below the surface: distance from wire axis is r2=a−a/2=a2r_2 = a - a/2 = \frac{a}{2}.
For r<ar < a, magnetic field inside a cylindrical wire with uniform current density:
B2=μ0Ir22πa2=μ0I(a/2)2πa2=μ0I4πa.B_2 = \frac{\mu_0 I r_2}{2\pi a^2} = \frac{\mu_0 I (a/2)}{2\pi a^2} = \frac{\mu_0 I}{4\pi a}.

3. Ratio of magnetic field at P1P_1 to that at P2P_2 (or inside to outside):
Wait, the question asks for the ratio of BB at a/2a/2 below to above or above to below:
In CBSE MS:
B(P1 inside at a/2)=μ0I4πa,B(P2 outside at 3a/2)=μ0I3πaB(P_1 \text{ inside at } a/2) = \frac{\mu_0 I}{4\pi a}, \quad B(P_2 \text{ outside at } 3a/2) = \frac{\mu_0 I}{3\pi a}

Ratio B(P2)B(P1)=μ0I/3πaμ0I/4πa=43\frac{B(P_2)}{B(P_1)} = \frac{\mu_0 I / 3\pi a}{\mu_0 I / 4\pi a} = \frac{4}{3}.
Hence, ratio is 4:34:3, matching option (c).
Chief Examiner Evaluation Report & Pitfalls:

Be careful to measure distances from the central axis of the wire, not from its surface.

4
Section A()
1 Mark
Which of the following waves cannot be polarized?
(a) Radio waves
(b) Ultraviolet rays
(c) X-rays
(d) Sound waves in air
CBSE Official Step-Marking AllocationTotal: 1 M
State that polarization is a property exhibited exclusively by transverse waves
+0.5 M
Identify sound waves as longitudinal waves that cannot be polarized (d)
+0.5 M
NCERT / CBSE Model Answer
Correct Option: (d) Sound waves in air
Reasoning:
Only transverse waves can be polarized because polarization is the restriction of vibrations of the wave to a single plane perpendicular to the direction of propagation. Sound waves in air are longitudinal waves, where particles oscillate parallel to the direction of propagation. Hence, sound waves cannot be polarized.
Chief Examiner Evaluation Report & Pitfalls:

Polarization is the definitive experimental proof of the transverse nature of electromagnetic waves.

5
Section A()
1 Mark
An electric dipole of moment p⃗\vec{p} is placed in a uniform electric field E⃗\vec{E}. The torque acting on the dipole and the potential energy of the dipole are respectively:
(a) τ⃗=p⃗×E⃗\vec{\tau} = \vec{p} \times \vec{E} and U=−p⃗⋅E⃗U = -\vec{p} \cdot \vec{E}
(b) τ⃗=p⃗⋅E⃗\vec{\tau} = \vec{p} \cdot \vec{E} and U=−p⃗×E⃗U = -\vec{p} \times \vec{E}
(c) τ⃗=E⃗×p⃗\vec{\tau} = \vec{E} \times \vec{p} and U=p⃗⋅E⃗U = \vec{p} \cdot \vec{E}
(d) τ⃗=p⃗×E⃗\vec{\tau} = \vec{p} \times \vec{E} and U=p⃗⋅E⃗U = \vec{p} \cdot \vec{E}
CBSE Official Step-Marking AllocationTotal: 1 M
State torque vector formula τ⃗=p⃗×E⃗\vec{\tau} = \vec{p} \times \vec{E}
+0.5 M
State potential energy scalar formula U=−p⃗⋅E⃗U = -\vec{p} \cdot \vec{E} and select (a)
+0.5 M
NCERT / CBSE Model Answer
Correct Option: (a) τ⃗=p⃗×E⃗\vec{\tau} = \vec{p} \times \vec{E} and U=−p⃗⋅E⃗U = -\vec{p} \cdot \vec{E}
Reasoning:
1. Torque on an electric dipole in an electric field is given by vector cross product: τ⃗=p⃗×E⃗\vec{\tau} = \vec{p} \times \vec{E} (magnitude τ=pEsin⁡θ\tau = pE \sin\theta).
2. Electrostatic potential energy of the dipole is given by scalar dot product: U=−p⃗⋅E⃗=−pEcos⁡θU = -\vec{p} \cdot \vec{E} = -pE \cos\theta, with zero reference taken at θ=90∘\theta = 90^\circ.
Chief Examiner Evaluation Report & Pitfalls:

Do not swap the order of the cross product: $\vec{p} \times \vec{E} = -(\vec{E} \times \vec{p})$.

6
Section A()
1 Mark
In a series LCR circuit, the voltage across each of the components R,L,R, L, and CC is 10 V10\text{ V}. If the capacitor is short-circuited, the voltage across the inductor will become:
(a) 10 V10\text{ V}
(b) 102 V10\sqrt{2}\text{ V}
(c) 102 V\frac{10}{\sqrt{2}}\text{ V}
(d) 5 V5\text{ V}
CBSE Official Step-Marking AllocationTotal: 1 M
Determine source voltage V=10 VV = 10\text{ V} and XL=RX_L = R from resonance condition
+0.5 M
Calculate impedance of RL circuit Z=R2Z = R\sqrt{2} and VL′=10/2 VV_L' = 10/\sqrt{2}\text{ V}
+0.5 M
NCERT / CBSE Model Answer
Correct Option: (c) 102 V\frac{10}{\sqrt{2}}\text{ V}
Working:
1. Initially, in the series LCR circuit, VR=VL=VC=10 VV_R = V_L = V_C = 10\text{ V}.
Since VL=VCV_L = V_C, the circuit is in resonance, so XL=XC=RX_L = X_C = R.
The source voltage is V=VR2+(VL−VC)2=VR=10 VV = \sqrt{V_R^2 + (V_L - V_C)^2} = V_R = 10\text{ V}.
2. When capacitor CC is short-circuited, the circuit becomes a series RL circuit with XL=RX_L = R.
Total impedance: Z=R2+XL2=R2+R2=R2Z = \sqrt{R^2 + X_L^2} = \sqrt{R^2 + R^2} = R\sqrt{2}.
3. The new current is I′=VZ=10R2I' = \frac{V}{Z} = \frac{10}{R\sqrt{2}}.
Voltage across the inductor is:
VL′=I′XL=(10R2)R=102 V.V_L' = I' X_L = \left(\frac{10}{R\sqrt{2}}\right) R = \frac{10}{\sqrt{2}}\text{ V}.
Chief Examiner Evaluation Report & Pitfalls:

At resonance, the net reactive voltage $(V_L - V_C) = 0$, so the entire applied voltage appears across the resistor.

7
Section A()
1 Mark
The magnetic susceptibility χm\chi_m of a material is −0.00002-0.00002. The material is:
(a) Paramagnetic
(b) Diamagnetic
(c) Ferromagnetic
(d) Non-magnetic
CBSE Official Step-Marking AllocationTotal: 1 M
Recall that diamagnetic materials have small and negative susceptibility χ<0\chi < 0
+0.5 M
Identify diamagnetic material and select option (b)
+0.5 M
NCERT / CBSE Model Answer
Correct Option: (b) Diamagnetic
Reasoning:
Diamagnetic materials have a small, negative magnetic susceptibility (−1≤χm<0-1 \leq \chi_m < 0). Since χm=−0.00002\chi_m = -0.00002 is negative and very small in magnitude, the material is diamagnetic.
- Paramagnetic materials have small, positive susceptibility (0<χm<ϵ0 < \chi_m < \epsilon).
- Ferromagnetic materials have large, positive susceptibility (χm≫1\chi_m \gg 1).
Chief Examiner Evaluation Report & Pitfalls:

Susceptibility $\chi < 0$ always indicates diamagnetism and relative permeability $\mu_r = 1 + \chi < 1$.

8
Section A()
1 Mark
An alpha particle of energy EE is projected towards a gold nucleus (Z=79Z = 79). The distance of closest approach is dd. If the energy of the alpha particle is doubled, the distance of closest approach will become:
(a) 2d2d
(b) d/2d/2
(c) 4d4d
(d) d/4d/4
CBSE Official Step-Marking AllocationTotal: 1 M
State distance of closest approach formula: d∝1/Ed \propto 1/E
+0.5 M
Conclude that doubling energy halves the distance: d′=d/2d' = d/2 (b)
+0.5 M
NCERT / CBSE Model Answer
Correct Option: (b) d/2d/2
Working:
At the distance of closest approach dd, the entire kinetic energy EE of the alpha particle is converted into electrostatic potential energy:
E=14πϵ0(2e)(Ze)d  ⟹  d=14πϵ02Ze2EE = \frac{1}{4\pi \epsilon_0} \frac{(2e)(Ze)}{d} \implies d = \frac{1}{4\pi \epsilon_0} \frac{2Ze^2}{E}

Thus, d∝1Ed \propto \frac{1}{E}.
When the kinetic energy is doubled (E′=2EE' = 2E):
d′=d2.d' = \frac{d}{2}.
Chief Examiner Evaluation Report & Pitfalls:

Distance of closest approach is inversely proportional to kinetic energy and directly proportional to atomic number $Z$.

9
Section A()
1 Mark
A convex lens of refractive index 1.51.5 has focal length ff in air. When immersed in water (refractive index 4/34/3), its focal length will become:
(a) ff
(b) 2f2f
(c) 4f4f
(d) f/4f/4
CBSE Official Step-Marking AllocationTotal: 1 M
Apply Lens Maker's formula in air: 1/f=(1.5−1)K=0.5K1/f = (1.5 - 1)K = 0.5K
+0.5 M
Apply in water: 1/fw=(9/8−1)K=K/8  ⟹  fw=4f1/f_w = (9/8 - 1)K = K/8 \implies f_w = 4f
+0.5 M
NCERT / CBSE Model Answer
Correct Option: (c) 4f4f
Working:
By Lens Maker's formula:
1fair=(ng−1)(1R1−1R2)=(1.5−1)K=0.5K=12K  ⟹  K=2f\frac{1}{f_{\text{air}}} = (n_g - 1)\left(\frac{1}{R_1} - \frac{1}{R_2}\right) = (1.5 - 1) K = 0.5 K = \frac{1}{2} K \implies K = \frac{2}{f}

When immersed in water:
1fwater=(ngnw−1)K=(1.54/3−1)K=(98−1)K=18K\frac{1}{f_{\text{water}}} = \left(\frac{n_g}{n_w} - 1\right) K = \left(\frac{1.5}{4/3} - 1\right) K = \left(\frac{9}{8} - 1\right) K = \frac{1}{8} K

Substituting K=2fK = \frac{2}{f}:
1fwater=18(2f)=14f  ⟹  fwater=4f.\frac{1}{f_{\text{water}}} = \frac{1}{8} \left(\frac{2}{f}\right) = \frac{1}{4f} \implies f_{\text{water}} = 4f.
Chief Examiner Evaluation Report & Pitfalls:

Remember that relative refractive index ${_w}n_g = n_g / n_w$ must be used when a lens is immersed in a liquid.

10
Section A()
1 Mark
The bending of light around the corners of an obstacle or aperture and its spread into the geometric shadow is called:
(a) Refraction
(b) Diffraction
(c) Dispersion
(d) Polarization
CBSE Official Step-Marking AllocationTotal: 1 M
State standard wave optics definition of diffraction
+0.5 M
Select option (b) Diffraction
+0.5 M
NCERT / CBSE Model Answer
Correct Option: (b) Diffraction
Reasoning:
By definition, diffraction is the phenomenon of bending of light around the edges of an obstacle or an aperture whose size is comparable to the wavelength of light, and its encroachment into the region of geometrical shadow.
Chief Examiner Evaluation Report & Pitfalls:

Diffraction is most pronounced when the size of the obstacle/slit is comparable to the wavelength of the incident wave.

11
Section A()
1 Mark
In a p-n junction diode, the barrier potential depends on:
(a) Doping level and nature of semiconductor material
(b) Geometry of the diode
(c) Applied forward voltage only
(d) Cross-sectional area of the diode
CBSE Official Step-Marking AllocationTotal: 1 M
State factors affecting barrier potential: semiconductor material, doping concentration, temperature
+0.5 M
Select option (a)
+0.5 M
NCERT / CBSE Model Answer
Correct Option: (a) Doping level and nature of semiconductor material
Reasoning:
The height of the potential barrier across a p-n junction depends on:
1. Nature of the semiconductor material (e.g. ≈0.7 V\approx 0.7\text{ V} for Si, ≈0.3 V\approx 0.3\text{ V} for Ge).
2. Amount of doping (doping density in p and n regions).
3. Temperature of the junction.
It is independent of physical shape, area, or geometry.
Chief Examiner Evaluation Report & Pitfalls:

Barrier potential is an intrinsic junction property determined by bandgap and doping concentration.

12
Section A()
1 Mark
A wire of resistance RR is stretched such that its radius decreases by 0.1%0.1\%. The percentage increase in its resistance is:
(a) +0.1%+0.1\%
(b) +0.2%+0.2\%
(c) +0.4%+0.4\%
(d) +0.8%+0.8\%
CBSE Official Step-Marking AllocationTotal: 1 M
Express resistance in terms of radius keeping volume constant: R∝1/r4R \propto 1/r^4
+0.5 M
Use fractional derivative ΔR/R=−4(Δr/r)=−4(−0.1%)=+0.4%\Delta R/R = -4(\Delta r/r) = -4(-0.1\%) = +0.4\% (c)
+0.5 M
NCERT / CBSE Model Answer
Correct Option: (c) +0.4%+0.4\%
Working:
Volume of the wire remains constant during stretching: V=A⋅l=πr2l=constantV = A \cdot l = \pi r^2 l = \text{constant}.
l=Vπr2l = \frac{V}{\pi r^2}

Resistance of the wire:
R=ρlA=ρVπ2r4R = \rho \frac{l}{A} = \rho \frac{V}{\pi^2 r^4}

Taking logarithm and differentiating for small fractional changes:
ln⁡R=ln⁡(const)−4ln⁡r\ln R = \ln(\text{const}) - 4 \ln r

ΔRR=−4Δrr\frac{\Delta R}{R} = -4 \frac{\Delta r}{r}

Given Δrr=−0.1%\frac{\Delta r}{r} = -0.1\% (radius decreases by 0.1%0.1\%):
ΔRR=−4(−0.1%)=+0.4%.\frac{\Delta R}{R} = -4(-0.1\%) = +0.4\%.
Chief Examiner Evaluation Report & Pitfalls:

Remember $R \propto l^2$ if length changes, and $R \propto 1/r^4$ if radius/diameter changes at constant volume.

13
Section A()
1 Mark
Assertion (A): In an uncharged p-n junction, no net current flows across the junction.
Reason (R): In an unbiased p-n junction, the diffusion current of majority carriers is equal and opposite to the drift current of minority carriers.
(a) Both (A) and (R) are true and (R) is the correct explanation of (A).
(b) Both (A) and (R) are true but (R) is not the correct explanation of (A).
(c) (A) is true but (R) is false.
(d) (A) is false but (R) is true.
CBSE Official Step-Marking AllocationTotal: 1 M
Verify Assertion is true: uncharged/unbiased junction has zero net current
+0.5 M
Verify Reason is true: diffusion and drift currents cancel exactly at equilibrium, explaining (A)
+0.5 M
NCERT / CBSE Model Answer
Correct Option: (a) Both (A) and (R) are true and (R) is the correct explanation of (A).
Analysis:
- Assertion (A): In thermal equilibrium without any applied external bias, there is no net electrical current flowing across the p-n junction (Inet=0I_{\text{net}} = 0). Hence, Assertion is TRUE.
- Reason (R): The concentration gradient drives diffusion of holes (p to n) and electrons (n to p), producing diffusion current. Meanwhile, the built-in electric field drives minority carriers across the depletion layer, producing drift current. At equilibrium, Idiffusion=IdriftI_{\text{diffusion}} = I_{\text{drift}} in opposite directions, resulting in zero net current. Reason is TRUE.
- Reason (R) correctly explains Assertion (A).
Chief Examiner Evaluation Report & Pitfalls:

Diffusion current and drift current flow in opposite directions across a p-n junction; equilibrium is achieved when they balance.

14
Section A()
1 Mark
Assertion (A): The core of a transformer is laminated to reduce eddy current loss.
Reason (R): Large eddy currents are induced in a bulk metal block due to time-varying magnetic flux, which cause thermal dissipation of energy (I2RI^2 R).
(a) Both (A) and (R) are true and (R) is the correct explanation of (A).
(b) Both (A) and (R) are true but (R) is not the correct explanation of (A).
(c) (A) is true but (R) is false.
(d) (A) is false but (R) is true.
CBSE Official Step-Marking AllocationTotal: 1 M
Identify that lamination increases resistance across eddy current loops
+0.5 M
Confirm both statements are true and (R) correctly explains (A)
+0.5 M
NCERT / CBSE Model Answer
Correct Option: (a) Both (A) and (R) are true and (R) is the correct explanation of (A).
Analysis:
- Assertion (A): The magnetic core is built of thin insulated steel laminations placed parallel to magnetic flux lines. This breaks the closed conduction paths, vastly reducing eddy current losses. Assertion is TRUE.
- Reason (R): In a solid bulk conductor, alternating magnetic flux induces circulating eddy currents in closed loops of low resistance, dissipating significant energy as heat (I2RI^2R). Reason is TRUE.
- Reason (R) correctly provides the scientific basis for laminating transformer cores.
Chief Examiner Evaluation Report & Pitfalls:

Laminations must be insulated from one another (using lacquer or oxide layers) to effectively suppress eddy currents.

15
Section A()
1 Mark
Assertion (A): The photoelectric current increases with an increase in the frequency of incident radiation (above threshold frequency).
Reason (R): The kinetic energy of emitted photoelectrons depends directly on the frequency of the incident radiation.
(a) Both (A) and (R) are true and (R) is the correct explanation of (A).
(b) Both (A) and (R) are true but (R) is not the correct explanation of (A).
(c) (A) is true but (R) is false.
(d) (A) is false but (R) is true.
CBSE Official Step-Marking AllocationTotal: 1 M
Recognize that photocurrent depends on intensity, not frequency   ⟹  \implies (A) is false
+0.5 M
Verify Einstein's equation Kmax⁡=hν−Φ0  ⟹  K_{\max} = h\nu - \Phi_0 \implies (R) is true, select (d)
+0.5 M
NCERT / CBSE Model Answer
Correct Option: (d) (A) is false but (R) is true.
Analysis:
- Assertion (A): Photoelectric current depends on the intensity (number of incident photons per second) of incident radiation, NOT on the frequency of light (provided ν>ν0\nu > \nu_0). Thus, Assertion (A) is FALSE.
- Reason (R): By Einstein's photoelectric equation, Kmax⁡=hν−Φ0K_{\max} = h\nu - \Phi_0. The maximum kinetic energy of emitted photoelectrons increases linearly with frequency ν\nu. Thus, Reason (R) is TRUE.
Hence, (A) is false but (R) is true.
Chief Examiner Evaluation Report & Pitfalls:

Frequency determines kinetic energy and stopping potential; intensity determines the number of photoelectrons and saturation photocurrent.

16
Section A()
1 Mark
Assertion (A): A current-carrying solenoid tends to contract along its length.
Reason (R): Adjacent circular turns of the solenoid carry current in the same direction and attract each other.
(a) Both (A) and (R) are true and (R) is the correct explanation of (A).
(b) Both (A) and (R) are true but (R) is not the correct explanation of (A).
(c) (A) is true but (R) is false.
(d) (A) is false but (R) is true.
CBSE Official Step-Marking AllocationTotal: 1 M
State rule: parallel currents in the same direction attract each other
+0.5 M
Apply to adjacent turns of solenoid to explain contraction   ⟹  \implies option (a)
+0.5 M
NCERT / CBSE Model Answer
Correct Option: (a) Both (A) and (R) are true and (R) is the correct explanation of (A).
Analysis:
- Parallel currents flowing in the same direction attract each other by Ampere's force law.
- In a helical solenoid, current flows in the same sense across adjacent turns. Therefore, adjacent turns attract each other.
- This attractive force pulls the coils together, causing the solenoid to contract along its axial length.
- Both (A) and (R) are true, and (R) correctly explains (A).
Chief Examiner Evaluation Report & Pitfalls:

Contrast: turns attract axially (causing contraction), but diametrically opposite elements of the same loop repel (causing radial expansion).

17
Section B()
2 Marks
A platinum surface having a work function of 5.63 eV5.63\text{ eV} is illuminated by a monochromatic source of frequency 1.6×1015 Hz1.6 \times 10^{15}\text{ Hz}. What will be the minimum de Broglie wavelength associated with the ejected electrons?
CBSE Official Step-Marking AllocationTotal: 2 M
Calculate photon energy E=6.63 eVE = 6.63\text{ eV} and Kmax⁡=1.0 eVK_{\max} = 1.0\text{ eV}
+1 M
Compute minimum de Broglie wavelength λmin⁡=h2mK=1.227 nm\lambda_{\min} = \frac{h}{\sqrt{2mK}} = 1.227\text{ nm}
+1 M
NCERT / CBSE Model Answer
Solution:
1. Energy of incident photon:
E=hν=6.63×10−34×1.6×10151.6×10−19 eV=10.608×10−191.6×10−19 eV=6.63 eV.E = h\nu = \frac{6.63 \times 10^{-34} \times 1.6 \times 10^{15}}{1.6 \times 10^{-19}}\text{ eV} = \frac{10.608 \times 10^{-19}}{1.6 \times 10^{-19}}\text{ eV} = 6.63\text{ eV}.
2. Maximum Kinetic Energy of emitted electrons:
Kmax⁡=E−Φ0=6.63 eV−5.63 eV=1.0 eV.K_{\max} = E - \Phi_0 = 6.63\text{ eV} - 5.63\text{ eV} = 1.0\text{ eV}.

In Joules: Kmax⁡=1.0×1.6×10−19 J=1.6×10−19 JK_{\max} = 1.0 \times 1.6 \times 10^{-19}\text{ J} = 1.6 \times 10^{-19}\text{ J}.
3. Minimum de Broglie wavelength:
Minimum wavelength corresponds to maximum momentum (pmax⁡=2mKmax⁡p_{\max} = \sqrt{2m K_{\max}}):
λmin⁡=hpmax⁡=h2mKmax⁡\lambda_{\min} = \frac{h}{p_{\max}} = \frac{h}{\sqrt{2m K_{\max}}}

λmin⁡=1.227V nm=1.2271.0 nm=1.227 nm=1.23×10−9 m=12.3 A˚.\lambda_{\min} = \frac{1.227}{\sqrt{V}}\text{ nm} = \frac{1.227}{\sqrt{1.0}}\text{ nm} = 1.227\text{ nm} = 1.23 \times 10^{-9}\text{ m} = 12.3\text{ Å}.
Chief Examiner Evaluation Report & Pitfalls:

Maximum kinetic energy corresponds to minimum de Broglie wavelength because $\lambda = h/p$.

18
Section B()
Internal Choice (OR)2 Marks
A beam of light consisting of two wavelengths, 4000 A˚4000\text{ Å} and 6000 A˚6000\text{ Å}, is used to obtain interference fringes in a Young's double-slit experiment. What is the least distance from the central maximum where a dark fringe is obtained?
OR
In a single slit diffraction experiment, a slit of width dd is illuminated by red light of wavelength 650 nm650\text{ nm}. For what value of dd will the first maximum fall at an angle of diffraction of 30∘30^\circ?
CBSE Official Step-Marking AllocationTotal: 2 M
State dark fringe condition y=(2n−1)λD/2dy = (2n-1)\lambda D / 2d
+1 M
Identify least distance corresponds to λ1=4000 A˚\lambda_1 = 4000\text{ Å} at n=1  ⟹  y=λ1D2dn=1 \implies y = \frac{\lambda_1 D}{2d}
+1 M
NCERT / CBSE Model Answer
Solution:
For destructive interference (dark fringe), position from central maximum is:
y=(2n−1)λD2d,n=1,2,3,…y = (2n - 1) \frac{\lambda D}{2d}, \quad n = 1, 2, 3, \dots

For the first dark fringe (n=1n = 1):
y=λD2dy = \frac{\lambda D}{2d}

Comparing the two wavelengths λ1=4000 A˚\lambda_1 = 4000\text{ Å} and λ2=6000 A˚\lambda_2 = 6000\text{ Å}:
The dark fringe closest to the central maximum corresponds to the smaller wavelength λ1\lambda_1 with n=1n = 1:
ymin⁡=λ1D2d=4000×10−10D2d=2×10−7Dd m.y_{\min} = \frac{\lambda_1 D}{2d} = \frac{4000 \times 10^{-10} D}{2d} = \frac{2 \times 10^{-7} D}{d}\text{ m}.

Alternative Option Solution:

In single slit diffraction, secondary maxima occur at:
dsin⁡θ=(n+12)λ,n=1,2,3,…d \sin\theta = \left(n + \frac{1}{2}\right)\lambda, \quad n = 1, 2, 3, \dots

For the first secondary maximum (n=1n = 1):
dsin⁡θ=32λd \sin\theta = \frac{3}{2}\lambda

Given θ=30∘  ⟹  sin⁡30∘=0.5\theta = 30^\circ \implies \sin 30^\circ = 0.5, and λ=650 nm=650×10−9 m\lambda = 650\text{ nm} = 650 \times 10^{-9}\text{ m}:
d(0.5)=32(650×10−9)d (0.5) = \frac{3}{2} (650 \times 10^{-9})

d=3×650×10−9=1.95×10−6 m=1.95 μm.d = 3 \times 650 \times 10^{-9} = 1.95 \times 10^{-6}\text{ m} = 1.95\text{ }\mu\text{m}.
Chief Examiner Evaluation Report & Pitfalls:

Do not confuse secondary maxima of diffraction $(d \sin\theta = (n+1/2)\lambda)$ with minima $(d \sin\theta = n\lambda)$.

19
Section B()
2 Marks
A heating element connected across a battery of 100 V100\text{ V} having an internal resistance of 1 Ω1\,\Omega draws an initial current of 10 A10\text{ A} at room temperature 20.0∘C20.0^\circ\text{C} which settles after a few seconds to a steady value of 8.0 A8.0\text{ A}. What is the steady temperature of the heating element? Temperature coefficient of resistance averaged over the temperature range is α=1.70×10−4 ∘C−1\alpha = 1.70 \times 10^{-4}\,^\circ\text{C}^{-1}.
CBSE Official Step-Marking AllocationTotal: 2 M
Find initial and steady resistances: R1=9 ΩR_1 = 9\,\Omega and R2=11.5 ΩR_2 = 11.5\,\Omega
+1 M
Apply R2=R1(1+αΔT)R_2 = R_1(1+\alpha\Delta T) and solve for T2≈1654∘CT_2 \approx 1654^\circ\text{C}
+1 M
NCERT / CBSE Model Answer
Solution:
1. At initial room temperature T1=20.0∘CT_1 = 20.0^\circ\text{C}:
I1=VR1+r  ⟹  10=100R1+1  ⟹  R1+1=10  ⟹  R1=9 Ω.I_1 = \frac{V}{R_1 + r} \implies 10 = \frac{100}{R_1 + 1} \implies R_1 + 1 = 10 \implies R_1 = 9\,\Omega.

2. At steady temperature T2T_2 with current I2=8.0 AI_2 = 8.0\text{ A}:
I2=VR2+r  ⟹  8=100R2+1  ⟹  R2+1=12.5  ⟹  R2=11.5 Ω.I_2 = \frac{V}{R_2 + r} \implies 8 = \frac{100}{R_2 + 1} \implies R_2 + 1 = 12.5 \implies R_2 = 11.5\,\Omega.

3. Relation between resistance and temperature:
R2=R1[1+α(T2−T1)]R_2 = R_1[1 + \alpha(T_2 - T_1)]

R2−R1=R1α(T2−T1)R_2 - R_1 = R_1 \alpha (T_2 - T_1)

11.5−9=9(1.70×10−4)(T2−20)11.5 - 9 = 9 (1.70 \times 10^{-4}) (T_2 - 20)

2.5=15.3×10−4(T2−20)2.5 = 15.3 \times 10^{-4} (T_2 - 20)

T2−20=2.51.53×10−3≈1634∘CT_2 - 20 = \frac{2.5}{1.53 \times 10^{-3}} \approx 1634^\circ\text{C}

T2≈1634+20=1654∘C.T_2 \approx 1634 + 20 = 1654^\circ\text{C}.
Chief Examiner Evaluation Report & Pitfalls:

Always subtract the battery's internal resistance from total circuit resistance to isolate the element's resistance.

20
Section B()
2 Marks
A circular coil of NN turns and radius RR carries a current II. It is unwound and rewound to make another circular coil of 2N2N turns with radius R/2R/2. Current II remains unchanged. What is the ratio of magnetic moments of the two coils?
CBSE Official Step-Marking AllocationTotal: 2 M
State formula M=NIA=NIπR2M = NIA = NI\pi R^2
+0.5 M
Substitute N2=2NN_2 = 2N and R2=R/2R_2 = R/2 to find M2=M1/2M_2 = M_1/2
+1 M
Conclude ratio M1:M2=2:1M_1 : M_2 = 2 : 1
+0.5 M
NCERT / CBSE Model Answer
Solution:
Magnetic dipole moment of a flat circular coil of NN turns, area AA, carrying current II is:
M=NIA=NI(πR2)M = N I A = N I (\pi R^2)

1. For the first coil:
M1=NI(πR2)M_1 = N I (\pi R^2)

2. For the second coil (N2=2N,R2=R/2N_2 = 2N, R_2 = R/2):
M2=N2I(πR22)=(2N)Iπ(R2)2=2NIπR24=12NIπR2=M12.M_2 = N_2 I (\pi R_2^2) = (2N) I \pi \left(\frac{R}{2}\right)^2 = 2N I \pi \frac{R^2}{4} = \frac{1}{2} N I \pi R^2 = \frac{M_1}{2}.

3. Ratio of magnetic moments:
M1M2=M1M1/2=21=2:1.\frac{M_1}{M_2} = \frac{M_1}{M_1/2} = \frac{2}{1} = 2:1.
Chief Examiner Evaluation Report & Pitfalls:

Even though the number of turns doubles, the area decreases by a factor of 4 ($R^2/4$), reducing the net magnetic moment by half.

21
Section B()
2 Marks
The ground state energy of a hydrogen atom is −13.6 eV-13.6\text{ eV}.
(i) What is the kinetic energy of an electron in the second excited state?
(ii) If the electron jumps to the ground state from the second excited state, calculate the wavelength of the emitted photon.
CBSE Official Step-Marking AllocationTotal: 2 M
(i) Identify n=3n=3, calculate E3=−1.51 eVE_3 = -1.51\text{ eV} and K3=+1.51 eVK_3 = +1.51\text{ eV}
+1 M
(ii) Compute ΔE=12.09 eV\Delta E = 12.09\text{ eV} and λ=hc/ΔE≈102.7 nm\lambda = hc/\Delta E \approx 102.7\text{ nm}
+1 M
NCERT / CBSE Model Answer
Solution:
(i) The second excited state corresponds to principal quantum number n=3n = 3.
Total energy in state nn is:
En=−13.6n2 eV=−13.632=−13.69=−1.51 eV.E_n = \frac{-13.6}{n^2}\text{ eV} = \frac{-13.6}{3^2} = \frac{-13.6}{9} = -1.51\text{ eV}.

For Bohr orbits in hydrogen atom, kinetic energy is related to total energy by K=−EnK = -E_n:
K3=−(−1.51 eV)=+1.51 eV.K_3 = -(-1.51\text{ eV}) = +1.51\text{ eV}.
(ii) Energy of emitted photon when jumping from n=3n = 3 to n=1n = 1:
ΔE=E3−E1=−1.51 eV−(−13.6 eV)=12.09 eV.\Delta E = E_3 - E_1 = -1.51\text{ eV} - (-13.6\text{ eV}) = 12.09\text{ eV}.

Wavelength of the emitted photon:
λ=hcΔE=1242 eV⋅nm12.09 eV≈102.7 nm=1.03×10−7 m.\lambda = \frac{hc}{\Delta E} = \frac{1242\text{ eV}\cdot\text{nm}}{12.09\text{ eV}} \approx 102.7\text{ nm} = 1.03 \times 10^{-7}\text{ m}.
Chief Examiner Evaluation Report & Pitfalls:

Remember terminology: 'ground state' is $n=1$, 'first excited state' is $n=2$, and 'second excited state' is $n=3$.

22
Section C()
3 Marks
Which device is used to convert AC into DC? State its underlying principle and explain its working as a full-wave rectifier with the help of a circuit diagram and input-output waveforms.
CBSE Official Step-Marking AllocationTotal: 3 M
Name semiconductor diode and state unidirectional conduction principle
+1 M
Explain operation during positive and negative half cycles with conduction states of D1,D2D_1, D_2
+1 M
Describe circuit configuration and draw/explain input-output waveforms (fout=2finf_{\text{out}} = 2f_{\text{in}})
+1 M
NCERT / CBSE Model Answer
Solution:
1. Device: A p-n junction diode (or semiconductor diode) is used as a rectifier to convert AC into DC.
2. Underlying Principle:
A p-n junction diode offers very low resistance when forward biased (permitting electric current to flow) and very high resistance when reverse biased (blocking electric current). Thus, it permits current conduction in one direction only.
3. Full-Wave Rectifier Working:
- A center-tapped transformer provides two anti-phase AC voltages to two diodes D1D_1 and D2D_2.
- During positive half-cycle: Upper terminal AA is positive and lower terminal BB is negative with respect to center tap CC. Diode D1D_1 is forward biased and conducts, while diode D2D_2 is reverse biased and non-conducting. Current flows through load resistor RLR_L from XX to YY.
- During negative half-cycle: Terminal AA is negative and terminal BB is positive. Diode D1D_1 is reverse biased and diode D2D_2 is forward biased and conducts. Current again flows through load resistor RLR_L in the same direction from XX to YY.
- Since output current across RLR_L is unidirectional for both half-cycles, full-wave rectification is achieved at double the input frequency (fout=2finf_{\text{out}} = 2 f_{\text{in}}).
Chief Examiner Evaluation Report & Pitfalls:

Emphasize that the current through the load resistor $R_L$ flows in the EXACT SAME direction during both half-cycles.

23
Section C()
3 Marks
(a) Why do transition metals exhibit higher enthalpies of atomization?
(b) Differentiate between nuclear fission and nuclear fusion with one example of each.
(c) The half-life of a radioactive substance is 30 days. Find the time taken for 7/87/8th of its initial mass to disintegrate.
CBSE Official Step-Marking AllocationTotal: 3 M
(a) Explain role of (n−1)d(n-1)d unpaired electrons in metallic-covalent bonding
+1 M
(b) Differentiate fission and fusion with balanced equations
+1 M
(c) Set N/N0=1/8=(1/2)3  ⟹  t=3×30=90 daysN/N_0 = 1/8 = (1/2)^3 \implies t = 3 \times 30 = 90\text{ days}
+1 M
NCERT / CBSE Model Answer
Solution:
(a) Transition metals have a large number of unpaired electrons in their (n−1)d(n-1)d subshells. These participate in extensive interatomic covalent bonding in addition to metallic bonding. The presence of strong metallic and covalent bonds results in high lattice cohesion and high enthalpy of atomization.
(b) Nuclear Fission vs Fusion:
- Nuclear Fission: A heavy unstable nucleus splits into two lighter nuclei of comparable masses with the release of large energy and neutrons.
Example: 92235U+01n→56141Ba+3692Kr+301n+200 MeV^{235}_{92}\text{U} + ^1_0\text{n} \to ^{141}_{56}\text{Ba} + ^{92}_{36}\text{Kr} + 3^1_0\text{n} + 200\text{ MeV}.
- Nuclear Fusion: Two lighter nuclei fuse together at extremely high temperature and pressure to form a heavier, more stable nucleus with release of massive energy.
Example: 12H+13H→24He+01n+17.6 MeV^2_1\text{H} + ^3_1\text{H} \to ^4_2\text{He} + ^1_0\text{n} + 17.6\text{ MeV}.
(c) Radioactive Decay Calculation:
Fraction remaining undisintegrated: N/N0=1−7/8=1/8N/N_0 = 1 - 7/8 = 1/8.
We know N/N0=(1/2)nN/N_0 = (1/2)^n, where n=t/T1/2n = t / T_{1/2}.
(12)n=18=(12)3  ⟹  n=3.\left(\frac{1}{2}\right)^n = \frac{1}{8} = \left(\frac{1}{2}\right)^3 \implies n = 3.

Time taken: t=n×T1/2=3×30 days=90 dayst = n \times T_{1/2} = 3 \times 30\text{ days} = 90\text{ days}.
Chief Examiner Evaluation Report & Pitfalls:

If $7/8$th disintegrates, the fraction REMAINING is $1 - 7/8 = 1/8$. Don't mistakenly set $N/N_0 = 7/8$.

24
Section C()
3 Marks
An alternating voltage V=V0sin⁡ωtV = V_0 \sin\omega t is applied across a series combination of an inductor LL and a resistor RR. Derive expressions for the impedance of the circuit and the phase difference between current and voltage. Draw the phasor diagram.
CBSE Official Step-Marking AllocationTotal: 3 M
Draw phasor diagram showing VLV_L leading current by π/2\pi/2 and VRV_R in phase
+1 M
Derive total voltage V=IR2+XL2V = I\sqrt{R^2 + X_L^2} and impedance Z=R2+(ωL)2Z = \sqrt{R^2 + (\omega L)^2}
+1 M
Derive phase angle tan⁡ϕ=ωL/R\tan\phi = \omega L / R
+1 M
NCERT / CBSE Model Answer
Solution:
1. Phasor Representation:
Let current in the series circuit be I=I0sin⁡ωtI = I_0 \sin\omega t.
- Voltage across resistor VR=IRV_R = I R is in phase with current II.
- Voltage across inductor VL=IXLV_L = I X_L leads current II by a phase angle of π/2\pi/2 (90∘90^\circ).
2. Resultant Voltage:
From the phasor diagram, VRV_R is along the X-axis and VLV_L is along the +Y+Y-axis.
V2=VR2+VL2=(IR)2+(IXL)2=I2(R2+XL2)V^2 = V_R^2 + V_L^2 = (I R)^2 + (I X_L)^2 = I^2 (R^2 + X_L^2)

V=IR2+XL2V = I \sqrt{R^2 + X_L^2}
3. Impedance ZZ:
Z=VI=R2+XL2=R2+(ωL)2.Z = \frac{V}{I} = \sqrt{R^2 + X_L^2} = \sqrt{R^2 + (\omega L)^2}.
4. Phase Difference ϕ\phi:
The voltage leads the current by phase angle ϕ\phi given by:
tan⁡ϕ=VLVR=IXLIR=XLR=ωLR\tan\phi = \frac{V_L}{V_R} = \frac{I X_L}{I R} = \frac{X_L}{R} = \frac{\omega L}{R}

ϕ=tan⁡−1(ωLR).\phi = \tan^{-1}\left(\frac{\omega L}{R}\right).
Chief Examiner Evaluation Report & Pitfalls:

In inductive circuits (RL), voltage leads current by $\phi$, where $0 < \phi < \pi/2$.

25
Section C()
3 Marks
A ray of light passes through an equilateral glass prism such that the angle of incidence is equal to the angle of emergence and each is equal to 3/43/4th of the angle of the prism. Calculate:
(i) the angle of minimum deviation,
(ii) the refractive index of the prism glass.
CBSE Official Step-Marking AllocationTotal: 3 M
Identify A=60∘A = 60^\circ and i=e=45∘i = e = 45^\circ
+0.5 M
Compute Dm=i+e−A=90∘−60∘=30∘D_m = i + e - A = 90^\circ - 60^\circ = 30^\circ
+1 M
Apply prism formula to find n=sin⁡45∘/sin⁡30∘=2n = \sin 45^\circ / \sin 30^\circ = \sqrt{2}
+1.5 M
NCERT / CBSE Model Answer
Solution:
For an equilateral prism, prism angle A=60∘A = 60^\circ.
Given i=e=34A=34(60∘)=45∘i = e = \frac{3}{4} A = \frac{3}{4}(60^\circ) = 45^\circ.
(i) Angle of minimum deviation (DmD_m):
When i=ei = e, the prism is in the condition of minimum deviation:
A+Dm=i+eA + D_m = i + e

60∘+Dm=45∘+45∘=90∘60^\circ + D_m = 45^\circ + 45^\circ = 90^\circ

Dm=90∘−60∘=30∘.D_m = 90^\circ - 60^\circ = 30^\circ.
(ii) Refractive index of prism material (nn):
Using the prism formula:
n=sin⁡(A+Dm2)sin⁡(A2)n = \frac{\sin\left(\frac{A + D_m}{2}\right)}{\sin\left(\frac{A}{2}\right)}

n=sin⁡(60∘+30∘2)sin⁡(60∘2)=sin⁡45∘sin⁡30∘=1/21/2=22=2≈1.414.n = \frac{\sin\left(\frac{60^\circ + 30^\circ}{2}\right)}{\sin\left(\frac{60^\circ}{2}\right)} = \frac{\sin 45^\circ}{\sin 30^\circ} = \frac{1/\sqrt{2}}{1/2} = \frac{2}{\sqrt{2}} = \sqrt{2} \approx 1.414.
Chief Examiner Evaluation Report & Pitfalls:

The condition $i = e$ strictly corresponds to minimum deviation $D = D_m$ and ray traversing symmetrically through the prism parallel to its base.

26
Section C()
3 Marks
(a) State the principle of a Moving Coil Galvanometer (MCG).
(b) Explain the importance of a radial magnetic field in an MCG and how it is achieved.
(c) Define current sensitivity and voltage sensitivity of a galvanometer.
CBSE Official Step-Marking AllocationTotal: 3 M
(a) State principle: current-carrying coil experiences torque balanced by restoring couple
+1 M
(b) Explain radial field ensures θ=90∘  ⟹  ϕ∝I\theta=90^\circ \implies \phi \propto I (linear scale); achieved via cylindrical poles and soft iron core
+1 M
(c) Define current sensitivity NAB/kNAB/k and voltage sensitivity NAB/kRNAB/kR
+1 M
NCERT / CBSE Model Answer
Solution:
(a) Principle: When a current-carrying coil is placed in a magnetic field, it experiences a deflecting torque τ=NIABsin⁡θ\tau = N I A B \sin\theta. Under equilibrium, this deflecting torque is balanced by the restoring torque τ=kϕ\tau = k\phi provided by the suspension fiber/spring (NIAB=kϕN I A B = k \phi).
(b) Radial Magnetic Field:
- Importance: In a radial field, the plane of the coil is always parallel to magnetic field lines (θ=90∘\theta = 90^\circ) in all angular positions. Hence, deflecting torque is always constant and maximum: τ=NIAB\tau = N I A B. This makes deflection directly proportional to current: ϕ∝I\phi \propto I, producing a linear scale.
- How achieved: By using concave cylindrical magnetic pole pieces along with a soft iron cylindrical core placed coaxially between the poles.
(c) Sensitivities:
- Current Sensitivity (IsI_s): Deflection produced per unit current: Is=ϕI=NABkI_s = \frac{\phi}{I} = \frac{N A B}{k} (rad/A or div/A).
- Voltage Sensitivity (VsV_s): Deflection produced per unit voltage: Vs=ϕV=NABkRV_s = \frac{\phi}{V} = \frac{N A B}{k R} (rad/V or div/V).
Chief Examiner Evaluation Report & Pitfalls:

Increasing current sensitivity by doubling $N$ also doubles resistance $R$, leaving voltage sensitivity unchanged.

27
Section C()
3 Marks
Identify the electromagnetic wave whose wavelength lies in the range:
(a) 10−10 m10^{-10}\text{ m}
(b) 10−4 m10^{-4}\text{ m}
(c) 10−1 m10^{-1}\text{ m}
State one important practical application for each of these three waves.
CBSE Official Step-Marking AllocationTotal: 3 M
Identify (a) X-rays and state medical diagnosis / bone fracture application
+1 M
Identify (b) Infrared rays and state remote control / thermal imaging application
+1 M
Identify (c) Microwaves and state radar / microwave oven application
+1 M
NCERT / CBSE Model Answer
Solution:
(a) λ=10−10 m\lambda = 10^{-10}\text{ m} (1 A˚1\text{ Å}):
- Identification: X-rays (wavelength range: 10−8 m10^{-8}\text{ m} to 10−12 m10^{-12}\text{ m}).
- Application: Used as a diagnostic tool in medicine to detect bone fractures, in radiotherapy to treat malignant tumors, and in crystallography to study crystal structures.
(b) λ=10−4 m\lambda = 10^{-4}\text{ m} (0.1 mm0.1\text{ mm}):
- Identification: Infrared rays (IR) (wavelength range: 700 nm700\text{ nm} to 1 mm1\text{ mm}).
- Application: Used in night vision devices, TV remote control systems, physical therapy (heat therapy), and infrared photography/satellite imaging.
(c) λ=10−1 m\lambda = 10^{-1}\text{ m} (10 cm10\text{ cm}):
- Identification: Microwaves (wavelength range: 1 mm1\text{ mm} to 0.1 m0.1\text{ m}).
- Application: Used in radar systems for aircraft navigation and speed detection, and in microwave ovens for rapid cooking and heating of food.
Chief Examiner Evaluation Report & Pitfalls:

Memorize the order of wavelengths: Gamma < X-rays < UV < Visible < IR < Microwaves < Radio waves.

28
Section C()
3 Marks
(a) Define an equipotential surface.
(b) Draw equipotential surfaces for:
(i) a uniform electric field pointing along the positive Z-direction,
(ii) an electric dipole.
(c) Why can two equipotential surfaces never intersect?
CBSE Official Step-Marking AllocationTotal: 3 M
(a) Define equipotential surface and zero work condition
+1 M
(b) Describe parallel planes for uniform field and dipole surfaces with V=0V=0 equatorial plane
+1 M
(c) Explain non-intersection: two potentials / two field directions at a single point is impossible
+1 M
NCERT / CBSE Model Answer
Solution:
(a) Definition: An equipotential surface is any surface over which the electric potential has the same constant value at every point. The work done in moving a charge between any two points on an equipotential surface is zero (W=qΔV=0W = q\Delta V = 0).
(b) Equipotential surfaces:
- (i) Uniform field along +Z+Z-direction: Equipotential surfaces are a family of parallel planes perpendicular to the Z-axis (parallel to the XY-plane).
- (ii) Electric dipole: Near each charge, equipotential surfaces are closed concentric, roughly spherical surfaces distorted closer together in the region between the charges; the equatorial bisector plane is an equipotential plane of zero potential (V=0V = 0).
(c) Why equipotential surfaces never intersect:
If two equipotential surfaces intersected, then at the point of intersection there would be two different values of electric potential, and electric field lines would point in two different directions simultaneously (as E⃗\vec{E} is perpendicular to the equipotential surface). This is physically impossible.
Chief Examiner Evaluation Report & Pitfalls:

Electric field lines are always normal to equipotential surfaces and point from higher to lower potential.

29
Section D()
Internal Choice (OR)4 Marks
Case Study Based Question: Motion of Charge in Magnetic Field
An electron with speed v0≪cv_0 \ll c enters perpendicularly into a uniform magnetic field B⃗\vec{B}. The magnetic Lorentz force F⃗=−e(v⃗×B⃗)\vec{F} = -e(\vec{v} \times \vec{B}) acting on the electron is perpendicular to both v⃗\vec{v} and B⃗\vec{B}. Consequently, the force provides the necessary centripetal acceleration, continuously deflecting the electron sideways without altering its kinetic energy, causing it to traverse a circular orbit of radius r0r_0.
Based on the above passage, answer the following questions:
(i) Why does the magnetic force do zero work on the moving electron? [1 Mark]
(ii) Derive the expression for the radius r0r_0 of the circular path. [1 Mark]
(iii) Show that the frequency of revolution of the electron in the magnetic field is independent of its speed and radius of the orbit. [2 Marks]
OR
(iii) If the speed of the electron is doubled, what will be the effect on: (a) the radius of its circular path, and (b) its time period of revolution? [2 Marks]
CBSE Official Step-Marking AllocationTotal: 4 M
(i) Explain F⃗⊥v⃗  ⟹  F⃗⋅dr⃗=0\vec{F} \perp \vec{v} \implies \vec{F} \cdot d\vec{r} = 0, work done is zero
+1 M
(ii) Equate centripetal force mv02/r0=ev0B  ⟹  r0=mv0/eBmv_0^2/r_0 = ev_0B \implies r_0 = mv_0 / eB
+1 M
(iii) Derive ν=eB/2πm\nu = eB / 2\pi m and demonstrate independence from v0v_0 and r0r_0
+2 M
NCERT / CBSE Model Answer
Solution:
(i) Magnetic Lorentz force F⃗m=q(v⃗×B⃗)\vec{F}_m = q(\vec{v} \times \vec{B}) is always perpendicular to instantaneous velocity v⃗\vec{v} (and displacement dr⃗=v⃗ dtd\vec{r} = \vec{v}\,dt).
Work done: dW=F⃗m⋅dr⃗=F⃗m⋅v⃗ dt=0dW = \vec{F}_m \cdot d\vec{r} = \vec{F}_m \cdot \vec{v}\,dt = 0 (since F⃗m⊥v⃗\vec{F}_m \perp \vec{v}). Hence, magnetic force does zero work.
(ii) The magnetic force provides the centripetal force:
mv02r0=ev0B  ⟹  r0=mv0eB.\frac{m v_0^2}{r_0} = e v_0 B \implies r_0 = \frac{m v_0}{e B}.
(iii) Time period of revolution:
T=2πr0v0=2πv0(mv0eB)=2πmeBT = \frac{2\pi r_0}{v_0} = \frac{2\pi}{v_0} \left(\frac{m v_0}{e B}\right) = \frac{2\pi m}{e B}

Frequency of revolution:
ν=1T=eB2πm.\nu = \frac{1}{T} = \frac{e B}{2\pi m}.

Since e,B,e, B, and mm are constants, the frequency ν\nu is independent of both the particle's speed v0v_0 and the orbital radius r0r_0.

Alternative Option Solution:

(a) Radius r0=mveB∝vr_0 = \frac{m v}{e B} \propto v. When speed is doubled (v′=2vv' = 2v), the radius of the circular path is doubled (r′=2r0r' = 2r_0).
(b) Time period T=2πmeBT = \frac{2\pi m}{e B} is independent of speed vv. Therefore, the time period remains unchanged.
Chief Examiner Evaluation Report & Pitfalls:

This cyclotron resonance principle is the operating basis of cyclotrons and magnetic mass spectrometers.

30
Section D()
Internal Choice (OR)4 Marks
Case Study Based Question: Photoelectric Effect
The emission of electrons from a metallic surface when irradiated by electromagnetic radiation of suitable frequency is known as the photoelectric effect. The emitted electrons are called photoelectrons. Experimental observations show that emission occurs instantaneously (time lag <10−9 s< 10^{-9}\text{ s}) once the frequency exceeds a characteristic threshold frequency ν0\nu_0. The maximum kinetic energy of photoelectrons depends linearly on the incident frequency, while the saturation photocurrent is directly proportional to the intensity of light.
Based on the above passage, answer the following questions:
(i) Define threshold frequency and work function of a metal. [1 Mark]
(ii) State Einstein's photoelectric equation. [1 Mark]
(iii) The work function of caesium is 2.14 eV2.14\text{ eV}. Find:
(a) its threshold frequency,
(b) the stopping potential when incident radiation has frequency 8.0×1014 Hz8.0 \times 10^{14}\text{ Hz}. [2 Marks]
OR
(iii) Plot a graph showing the variation of stopping potential with frequency of incident radiation for two different photosensitive metals A and B having work functions ΦA>ΦB\Phi_A > \Phi_B. State what the slope and intercepts of this graph represent. [2 Marks]
CBSE Official Step-Marking AllocationTotal: 4 M
(i) Define threshold frequency and work function Φ0=hν0\Phi_0 = h\nu_0
+1 M
(ii) Write Einstein's equation Kmax⁡=eV0=hν−Φ0K_{\max} = eV_0 = h\nu - \Phi_0
+1 M
(iii) Calculate ν0=5.16×1014 Hz\nu_0 = 5.16 \times 10^{14}\text{ Hz} and stopping potential V0=1.18 VV_0 = 1.18\text{ V}
+2 M
NCERT / CBSE Model Answer
Solution:
(i)
- Threshold Frequency (ν0\nu_0): The minimum frequency of incident radiation below which no photoemission occurs from a photosensitive surface, regardless of intensity.
- Work Function (Φ0\Phi_0): The minimum energy required to liberate an electron from the surface of a metal without imparting any kinetic energy (Φ0=hν0\Phi_0 = h\nu_0).
(ii) Einstein's Photoelectric Equation:
Kmax⁡=eV0=hν−Φ0=h(ν−ν0)K_{\max} = e V_0 = h\nu - \Phi_0 = h(\nu - \nu_0)

where hh is Planck's constant, ν\nu is incident frequency, and Φ0\Phi_0 is work function.
(iii)
(a) Threshold frequency ν0\nu_0:
ν0=Φ0h=2.14×1.6×10−19 J6.63×10−34 J⋅s=3.424×10−196.63×10−34=5.16×1014 Hz.\nu_0 = \frac{\Phi_0}{h} = \frac{2.14 \times 1.6 \times 10^{-19}\text{ J}}{6.63 \times 10^{-34}\text{ J}\cdot\text{s}} = \frac{3.424 \times 10^{-19}}{6.63 \times 10^{-34}} = 5.16 \times 10^{14}\text{ Hz}.

(b) Maximum kinetic energy and stopping potential V0V_0 at ν=8.0×1014 Hz\nu = 8.0 \times 10^{14}\text{ Hz}:
E=hν=6.63×10−34×8.0×10141.6×10−19 eV=53.04×10−201.6×10−19=3.315 eV.E = h\nu = \frac{6.63 \times 10^{-34} \times 8.0 \times 10^{14}}{1.6 \times 10^{-19}}\text{ eV} = \frac{53.04 \times 10^{-20}}{1.6 \times 10^{-19}} = 3.315\text{ eV}.

eV0=E−Φ0=3.315 eV−2.14 eV=1.175 eVe V_0 = E - \Phi_0 = 3.315\text{ eV} - 2.14\text{ eV} = 1.175\text{ eV}

∴V0=1.175 V≈1.18 V.\therefore V_0 = 1.175\text{ V} \approx 1.18\text{ V}.

Alternative Option Solution:

Graph of V0V_0 vs ν\nu is a straight line: V0=heν−Φ0eV_0 = \frac{h}{e}\nu - \frac{\Phi_0}{e}.
- Slope: he\frac{h}{e} (universal constant, identical for all metals).
- X-intercept: Threshold frequency ν0\nu_0.
- Y-intercept: −Φ0e-\frac{\Phi_0}{e}.
For metal A with ΦA>ΦB\Phi_A > \Phi_B, metal A will have a larger threshold frequency ν0A>ν0B\nu_{0A} > \nu_{0B}, so the line for A is shifted to the right of B with identical slope.
Chief Examiner Evaluation Report & Pitfalls:

The slope of stopping potential vs frequency graph is ALWAYS $h/e$, completely independent of the metal material.

31
Section E()
Internal Choice (OR)5 Marks
(I) (a) State two limitations of Ohm's law with graphical representations of their I-V characteristics.
(b) Derive the relationship between drift velocity of free electrons and electric current density in a conductor.
OR
(II) (a) State Kirchhoff's rules for an electrical network.
(b) Use Kirchhoff's rules to deduce the condition for balance in a Wheatstone bridge circuit.
CBSE Official Step-Marking AllocationTotal: 5 M
(a) State limitations of Ohm's law with non-linear/diode characteristics
+2 M
(b) Derive total charge Q=nAleQ = nAle, time t=l/vdt = l/v_d, I=neAvdI = neAv_d, and J=nevdJ = nev_d
+3 M
NCERT / CBSE Model Answer
Solution:
(I) (a) Limitations of Ohm's Law:
1. Non-linear V−IV-I characteristics: VV ceases to be proportional to II at high currents due to Joule heating, causing resistance to increase (e.g. filament of a torch bulb).
2. Direction dependence (non-ohmic rectifiers): The magnitude of current depends on the polarity of applied voltage. For example, a semiconductor diode conducts large current under forward bias and negligible current under reverse bias.
3. Negative resistance region: V−IV-I relation is not unique; current decreases with increasing voltage (e.g. GaAs, tunnel diode).
(b) Derivation of J=nevdJ = n e v_d:
- Consider a cylindrical conductor of length ll and uniform cross-sectional area AA.
- Let nn be the number density of free electrons (conduction electrons per unit volume).
- Total number of free electrons in volume AlAl is N=nAlN = n A l.
- Total free charge in this volume is Q=Ne=nAleQ = N e = n A l e.
- Under applied electric field EE, electrons drift with average velocity vdv_d.
- Time taken by this charge to cross length ll is t=lvdt = \frac{l}{v_d}.
- Electric current is:
I=Qt=nAlel/vd=neAvd.I = \frac{Q}{t} = \frac{n A l e}{l / v_d} = n e A v_d.

- Current density JJ is current per unit cross-sectional area:
J=IA=nevd.J = \frac{I}{A} = n e v_d.

In vector form: J⃗=−nev⃗d=σE⃗\vec{J} = -n e \vec{v}_d = \sigma \vec{E}.

Alternative Option Solution:

(a) Kirchhoff's Rules:
1. Kirchhoff's Current Law (Junction Rule): At any junction in an electrical circuit, the algebraic sum of all electric currents entering and leaving the junction is zero: ∑I=0\sum I = 0. This rule is based on the conservation of electric charge.
2. Kirchhoff's Voltage Law (Loop Rule): The algebraic sum of all potential changes (emf and IRIR drops) around any closed loop in an electrical network is zero: ∑ΔV=∑E−∑IR=0\sum \Delta V = \sum \mathcal{E} - \sum IR = 0. This rule is based on the conservation of energy.
(b) Wheatstone Bridge Balance Condition:
- Consider four resistors P,Q,R,SP, Q, R, S forming a closed bridge ABCDABCD with a galvanometer GG across BDBD and a battery E\mathcal{E} across ACAC.
- At balance, no current flows through the galvanometer (Ig=0I_g = 0), so VB=VDV_B = V_D.
- Current I1I_1 flows through arm ABAB and continues through arm BCBC.
- Current I2I_2 flows through arm ADAD and continues through arm DCDC.
- Applying Kirchhoff's loop rule to loop ABDAABDA (with Ig=0I_g = 0):
−I1P+I2R=0  ⟹  I1P=I2R…(1)-I_1 P + I_2 R = 0 \implies I_1 P = I_2 R \quad \dots (1)

- Applying loop rule to loop BCDBBCDB (with Ig=0I_g = 0):
−I1Q+I2S=0  ⟹  I1Q=I2S…(2)-I_1 Q + I_2 S = 0 \implies I_1 Q = I_2 S \quad \dots (2)

- Dividing equation (1) by equation (2):
I1PI1Q=I2RI2S  ⟹  PQ=RS.\frac{I_1 P}{I_1 Q} = \frac{I_2 R}{I_2 S} \implies \frac{P}{Q} = \frac{R}{S}.

This is the required Wheatstone bridge balance condition.
Chief Examiner Evaluation Report & Pitfalls:

Always mention the fundamental conservation laws behind Kirchhoff's rules: Junction rule = conservation of charge; Loop rule = conservation of energy.

32
Section E()
Internal Choice (OR)5 Marks
(I) Explain with the help of a labelled diagram the principle and working of an AC generator. Derive an expression for the instantaneous induced electromotive force (emf) when a coil of NN turns and area AA rotates at angular velocity ω\omega in a uniform magnetic field BB. What is the source of energy in this device?
OR
(II) (a) Describe the principle, construction, and working of a step-up transformer with a neat labelled diagram.
(b) Explain four main causes of energy losses in a practical transformer and how each loss is minimized.
CBSE Official Step-Marking AllocationTotal: 5 M
State electromagnetic induction principle and draw labelled diagram of AC generator
+1.5 M
Derive flux Φ=NBAcos⁡(ωt)\Phi = NBA\cos(\omega t) and instantaneous emf E=NBAωsin⁡(ωt)\mathcal{E} = NBA\omega\sin(\omega t)
+2.5 M
State mechanical energy of external turbine/prime mover is source of electrical energy
+1 M
NCERT / CBSE Model Answer
Solution:
(I) AC Generator:
1. Principle: Works on the principle of electromagnetic induction (Faraday's Law). When a closed coil rotates in a uniform magnetic field, the magnetic flux linked with the coil changes continuously, inducing an alternating emf across its terminals.
2. Derivation of Instantaneous EMF:
- Let a rectangular coil of NN turns and area AA rotate with constant angular frequency ω\omega in a uniform magnetic field BB.
- At time t=0t = 0, the normal to the coil is parallel to B⃗\vec{B}. At time tt, the angle between normal n^\hat{n} and field B⃗\vec{B} is θ=ωt\theta = \omega t.
- Magnetic flux linked with the coil at time tt:
ΦB=N(B⃗⋅A⃗)=NBAcos⁡(ωt).\Phi_B = N (\vec{B} \cdot \vec{A}) = N B A \cos(\omega t).

- By Faraday's Law of electromagnetic induction, induced emf is:
E=−dΦBdt=−ddt[NBAcos⁡(ωt)]=−NBA[−ωsin⁡(ωt)]\mathcal{E} = -\frac{d\Phi_B}{dt} = -\frac{d}{dt}[N B A \cos(\omega t)] = -N B A [-\omega \sin(\omega t)]

E=NBAωsin⁡(ωt)=E0sin⁡(ωt)\mathcal{E} = N B A \omega \sin(\omega t) = \mathcal{E}_0 \sin(\omega t)

where peak emf is E0=NBAω\mathcal{E}_0 = N B A \omega.
3. Source of Energy:
The mechanical work done by the external prime mover (e.g. falling water in hydro plants or steam turbines in thermal/nuclear plants) in rotating the coil against magnetic counter-torque is converted into electrical energy.

Alternative Option Solution:

(a) Step-Up Transformer:
- Principle: Mutual induction between two magnetically coupled coils.
- Working: Alternating current in the primary coil generates an alternating magnetic flux in the laminated soft iron core. This flux links with the secondary coil, inducing an emf: VsVp=NsNp=k\frac{V_s}{V_p} = \frac{N_s}{N_p} = k.
- In a step-up transformer, Ns>Np  ⟹  Vs>VpN_s > N_p \implies V_s > V_p and Is<IpI_s < I_p.
(b) Energy Losses in Transformers:
1. Joule Heating Loss (I2RI^2R): Resistance of primary and secondary windings causes thermal dissipation. Minimization: Use thick copper wires with low electrical resistivity.
2. Eddy Current Loss: Alternating flux induces eddy currents in the core. Minimization: Use a laminated core made of thin insulated sheets of high-resistivity silicon steel.
3. Hysteresis Loss: Repeated magnetization and demagnetization of the iron core dissipates energy as heat. Minimization: Use soft iron or permalloy with narrow hysteresis loop area.
4. Flux Leakage Loss: Not all magnetic flux generated by the primary links with the secondary coil. Minimization: Wind secondary coil directly over the primary coil (coaxial shell winding).
Chief Examiner Evaluation Report & Pitfalls:

Do not forget the negative sign in Faraday's law $\mathcal{E} = -d\Phi/dt$. The derivative of $\cos(\omega t)$ is $-\omega \sin(\omega t)$, canceling the negative sign.

33
Section E()
Internal Choice (OR)5 Marks
(I) (a) A giant astronomical refracting telescope at an observatory has an objective lens of focal length 15 m15\text{ m}. If an eyepiece of focal length 1.0 cm1.0\text{ cm} is used, what is the angular magnification of the telescope in normal adjustment?
(b) If this telescope is used to view the moon, what is the diameter of the image of the moon formed by the objective lens? (Diameter of the moon =3.48×106 m= 3.48 \times 10^6\text{ m}, radius of lunar orbit =3.8×108 m= 3.8 \times 10^8\text{ m}).
OR
(II) (a) State Huygens' principle for the propagation of wave fronts.
(b) Use Huygens' principle to verify Snell's law of refraction of a plane wave at a plane boundary separating two media.
CBSE Official Step-Marking AllocationTotal: 5 M
(a) Calculate angular magnification m=−fo/fe=−1500m = -f_o/f_e = -1500
+2 M
(b) Compute angular size α=3.48×106/3.8×108\alpha = 3.48 \times 10^6 / 3.8 \times 10^8 rad
+1.5 M
Calculate image diameter d=αfo=13.74 cmd = \alpha f_o = 13.74\text{ cm}
+1.5 M
NCERT / CBSE Model Answer
Solution:
(I) (a) Angular Magnification in Normal Adjustment:
Given focal length of objective fo=15 m=1500 cmf_o = 15\text{ m} = 1500\text{ cm}.
Focal length of eyepiece fe=1.0 cmf_e = 1.0\text{ cm}.
In normal adjustment (final image formed at infinity):
m=−fofe=−1500 cm1.0 cm=−1500.m = -\frac{f_o}{f_e} = -\frac{1500\text{ cm}}{1.0\text{ cm}} = -1500.

Magnitude of angular magnification is 15001500 (image is inverted).
(b) Diameter of the Moon's Image:
Let DD be the actual diameter of the moon and d0d_0 be the distance to the moon (radius of lunar orbit).
Angle subtended by the moon at the objective lens:
α=DiameterDistance=3.48×106 m3.8×108 m≈0.916×10−2 radians.\alpha = \frac{\text{Diameter}}{\text{Distance}} = \frac{3.48 \times 10^6\text{ m}}{3.8 \times 10^8\text{ m}} \approx 0.916 \times 10^{-2}\text{ radians}.

Let dd be the diameter of the circular image of the moon formed at the focal plane of the objective lens (at distance fo=15 mf_o = 15\text{ m}):
α=dfo  ⟹  d=α×fo\alpha = \frac{d}{f_o} \implies d = \alpha \times f_o

d=(3.48×1063.8×108)×15 m=52.2×1063.8×108≈0.1374 m=13.74 cm.d = \left(\frac{3.48 \times 10^6}{3.8 \times 10^8}\right) \times 15\text{ m} = \frac{52.2 \times 10^6}{3.8 \times 10^8} \approx 0.1374\text{ m} = 13.74\text{ cm}.

Alternative Option Solution:

(a) Huygens' Principle:
1. Every point on a given primary wavefront acts as a fresh source of secondary spherical wavelets which travel in all directions with the speed of light in that medium.
2. The forward envelope (tangential surface) to these secondary wavelets at any later instant gives the new position of the wavefront.
(b) Verification of Snell's Law of Refraction:
- Consider a plane wavefront ABAB incident at angle ii on a plane surface XYXY separating medium 1 (velocity v1v_1) from medium 2 (velocity v2v_2, where v2<v1v_2 < v_1).
- Let time taken by the wave disturbance to travel from point BB to CC in medium 1 be τ\tau. Then BC=v1τBC = v_1 \tau.
- In the same time τ\tau, secondary wavelets from point AA expand into medium 2 over a radius AD=v2τAD = v_2 \tau.
- The tangent plane CDCD drawn from CC to this wavelet represents the refracted wavefront at angle rr.
- In right-angled triangle ΔABC\Delta ABC:
sin⁡i=BCAC=v1τAC\sin i = \frac{BC}{AC} = \frac{v_1 \tau}{AC}

- In right-angled triangle ΔADC\Delta ADC:
sin⁡r=ADAC=v2τAC\sin r = \frac{AD}{AC} = \frac{v_2 \tau}{AC}

- Dividing these two relations:
sin⁡isin⁡r=v1τ/ACv2τ/AC=v1v2=c/n1c/n2=n2n1=1n2.\frac{\sin i}{\sin r} = \frac{v_1 \tau / AC}{v_2 \tau / AC} = \frac{v_1}{v_2} = \frac{c / n_1}{c / n_2} = \frac{n_2}{n_1} = {_1n_2}.

n1sin⁡i=n2sin⁡r.n_1 \sin i = n_2 \sin r.

This verifies Snell's Law of refraction using wave theory.
Chief Examiner Evaluation Report & Pitfalls:

Moon image is formed at the focal plane of the objective because the object distance (moon's distance) is effectively at infinity.